Signal Connector SSHL Contact, 1.00mm Pitch SSHL Crimp Terminals for AWG#32 To 28 Wires

Quick Detail

Package & Delivery Lead Time

Detailed Description

1, The specification of the product including basic size information, electrical and mechanical properties. - - - - Basic size information | Termination Interface Style | crimp or compression | Processing methods | E-stamping before tin-plated or gold-flashed | Insulation O.D. | 0.80mm(Max) | Part No. | A1002-TPE/A1002-GPE | Application | signal | | Electricalproperties | Current Rating | 1A AC, DC | Voltage Rating | 50V AC, DC | Contact Resistance | 30m Max | Insulation Resistance | 100m min | Withstanding Voltage | 500V AC/minute | | Mechanical properties | Temperature range | -25 to 85 | Other information please kindly check the following picture. | - - - - 2, Related drawing and report Developed for PDP, LCD or small electronics equipment. This is a dual-row small crimp type connector with a secure locking system or without-designed for different applications. The PC board layout is compatible withthat of existing SHD connector, which allows for replacement of the above existing connector. Please kindly check the following information: - - - - 5. Mechanical Performance - - - - Test Description | Procedure | Requirement | 5-1 | Actuator Insertion & Withdrawal Force | Insert and withdraw connectors at the speed rate of 253mm / minute. | Refer to paragraph 7 | 5-2 | Crimping Pull Out Force | Fix the crimped terminal, apply axial pull out force on the wire at the speed rat of 253mm / minute.(Based upon JIS C5402 6.8) | AWG#28 | 1.0kgf (Min) | AWG#30 | 0.8kgf (Min) | AWG#32 | 0.5kgf (Min) | 5-3 | Terminal Insertion Force. | Insert the crimped terminal into the housing. | 0.50kgf (Max.) | 5-4 | Terminal/Housing Retention Force. | Apply axial pull out force at the speed rate of 253mm / minute on the terminal assembled in the housing. | 0.50kgf (Min.) | 5-5 | Pin Retention Force | Apply axial push force at the speed rate of 253mm / minute | 0.50kgf (Min.) | 5-6 | Durability | When mated up to 50 cycles repeatedly by the rate of 10 cycle per minute. | Contact Resistance 40m (Max.) | 5-7 | Vibration | Amplitude: 1.5mm P-P Sweep time: 10-55-10 Hz in 1 minute Duration: 2 hours in each X.Y.Z. axes. (Based upon MIL-STD-202 Method 201A) | Appearance No Damage. Contact Resistance 40m (Max.) Discontinuity 1 sec.(Max.) | 5-8 | Physical Shock | 490m/s50G,3 strokes in each X.Y.Z. axes. (Based upon JIS C0041/MIL-STD-202 Method 213B Cond. A) | - - - - | 6. Environmental Performance And Others - - - - Test Description | Procedure | Requirement | 6-1 | Temperature Rise | Carrying rated current load.(Based upon UL 498) | 30(Max.) | 6-2 | Heat Resistance | 852,96 hours (Based upon JIS C0021/MIL-STD-202 Method 108A Cond. A) | Appearance No Damage. Contact Resistance 40m (Max.) | 6-3 | Cold Resistance | -253,96 hours (Based upon JIS C0020) | 6-4 | Humidity | Temperature: 402 Relative Humidity : 90~95% Duration: 96 hours (Based upon JIS C0022/MIL-STD-202 Method 103B Cond. B) | Appearance No Damage. Contact Resistance 40m (Max.) Insulation Resistance 10M (Min.) Dielectric Withstanding Voltage Must meet 4-3 | 6-5 | Temperature Cycling | 5 cycles of: a) -55 30 minutes b) +85 30 minutes (Based upon JIS C0025) | Appearance No Damage. Contact Resistance 40m (Max.) | 6-6 | Salt Spray | Tin-plated 12 hours / Gold- plated 24 hours exposure to a salt spray from the 51% solution at 352. (Based upon JIS C0023/MIL-STD-202 Method 101C Cond. B) | 6-7 | SO2 Gas | 24 hours exposure to 505ppm. SO2 gas at 402. | 6-8 | NH3 Gas | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. | - - - - - - - - 6-9 | Solderability | Soldering Time: 50.5 sec. Solder Temperature: 2455 | Solder Wetting 95% of immersed area must show no voids, pin holes | 6-10 | Resistance to Soldering Heat | When reflowing Refer to paragraph 8 Solder iron method Soldering Time: 50.5 sec. Solder Temperature: 370 ~ 400 | Appearance No Damage. | - - - - 7. Actuator Insertion/Withdrawal Force [Unit : kgf] - - - - Circuits | At Initial | Circuits | At Initial | Insertion (Max.) | Withdrawal (Min.) | Insertion (Max.) | Withdrawal (Min.) | Single | 0.20 | 0.03 | 16 | 3.60 | 0.80 | 02 | 0.80 | 0.10 | 17 | 3.80 | 0.85 | 03 | 1.00 | 0.15 | 18 | 4.00 | 0.90 | 04 | 1.20 | 0.20 | 19 | 4.20 | 0.95 | 05 | 1.40 | 0.25 | 20 | 4.40 | 1.00 | 06 | 1.60 | 0.30 | 21 | 4.60 | 1.05 | 07 | 1.80 | 0.35 | 22 | 4.80 | 1.10 | 08 | 2.00 | 0.40 | 23 | 5.00 | 1.15 | 09 | 2.20 | 0.45 | 24 | 5.20 | 1.20 | 10 | 2.40 | 0.50 | 25 | 5.40 | 1.25 | 11 | 2.60 | 0.55 | 26 | 5.60 | 1.30 | 12 | 2.80 | 0.60 | 27 | 5.80 | 1.35 | 13 | 3.00 | 0.65 | 28 | 6.00 | 1.40 | 14 | 3.20 | 0.70 | 29 | 6.20 | 1.45 | 15 | 3.40 | 0.75 | 30 | 6.40 | 1.50 | - - - - | - - - - 4, FAQ Q:Do you allow multiple design per setup? A:Yes.We accept OEM/ODM service and allow multiple design per setup. Q:How long does shipping take? A:It depends on the destination location and quantity. In most developed country, delivery by Fed x/UPS/DHL is normally 2-3 days(excluding weekends). Q: How is the goods packaged ? A: Usually in PE bads, tube, pipeand with outsidecarton box. 5, we can offer multiple, safe and fast shippment for you! We have very good cooperation with world famouse delivery company, and the can offer us good service and favorable price. It's sure that every business between us will be fast and happy. Choose us! Let's connect the realistic and electronic world.

Basic Company Information

Dongguan Xinpei Plastic Metal Electronic Limited

Company Advantage

Detail Company Introduction